6 Common Problems With Ghost Control Gate Openers - DIY Smart Home Hub (2023)

6 Common Problems With Ghost Control Gate Openers - DIY Smart Home Hub (1)

Lifetime warranty with Ghost Controls gate opener helps homeownersEnjoy safe shoppingFor a long time. As long as you meet the service requirements, it will last for decades.

However, if you have any problems, the customer service representative will help you resolve the issue immediately.

So you don't have to worry about buying replacement components for your opener.

Just focus on it morecommit to a trusted dealer who offers decent policies to customers.

Doing business with an obscure supplier is never a good idea. I hope that way you don't have to worry about the safety of your purchase.

Most issues reported by customers can be easily resolved by following some quick fixes.

So, if you are looking for a Ghost Control gate opener for your home, it will be helpful to read this list of possible problems and solutions.

Ghost Controls Gate Opener-Problema:

  1. no movement of an arm

If you're not getting one-arm movement and the gate isn't moving upon entry, there's a good chance you're dealing with tension issues.

Any strain gauge can be used to reduce this problem. So,Get a multimeter and check battery performance.

6 Common Problems With Ghost Control Gate Openers - DIY Smart Home Hub (2)

If the output power is less than 12 volts, the only viable option is to replace the battery. However, if you are sure that the problem is not the battery, check the integrity of the control board and fuse.

  1. The door opens by itself

Customers also complain of problems opening the gate even when there is no vehicle near the entrance.

(Video) Off Grid Smart Ghost Gate Opener

This problem is mainly related to faulty vehicle sensors installed with the gate opener. Therefore, you need to recalibrate your vehicle's sensor to avoid these incorrect door opener entries.

For the recalibration process, you need to reconnect the red wire to the terminal block and theSensor only for about 15 minutes.

6 Common Problems With Ghost Control Gate Openers - DIY Smart Home Hub (3)

This should fix the issue with the door opening randomly even when no one is at the entrance.

  1. battery problems

Battery issues don't seem that serious, but they sure are annoying.

If the batteries are low, you will not receive any response from the device. Unfortunately, the battery ratings for Ghost Control Gate Opener are not good.

So, there is a good chance that you too are experiencing problems with the same errors. The only solution in this situation is to get a new replacement.

You really can't work with a runny pieceand buying a new one might be the only solution here. From there you can test the battery response again.

Ideally, a replacement will fix most machine power outages. However, this is what you should focus on.Get a compatible replacement.

6 Common Problems With Ghost Control Gate Openers - DIY Smart Home Hub (4)

If you spend money on an off-brand option, you'll go back to the same mistakes. So do yourself a favor and stick with reliable options.

The dealer will help point you in the right direction if you can't find the one that's right for your device. That way, you don't have to worry about wasting money on a faulty device.

(Video) Ghost Controls Gate Antenna Extension/Extend Range! #ghostcontrols #gatecontroller

  1. calibration problems

The situation where the arm exceeds or does not reach the desired opening and closing limit will create many problems.

This problem is not so rare when you first set up the device.. So if you're in the same boat, make sure you run the calibration routine again.

In the end you made sure the port was in the open orientation and thenwith the work keysto correct the configuration.

Once the unit is in the right place, you can do it.Press and hold the SET button, and that will be all when you set the location open.

From there, just wait for the alarm to sound and that marks the end of the calibration routine.

You must follow the same routine for the indoor location.and then click the 1st and 2nd SET button when the position is perfect.

  1. Auto close features do not work

The auto close feature is one of the most important parts of this system, but some owners have complained that this feature doesn't work.

Fortunately, these errors are mostly related to the settings and not the hardware side.Here's a quick way to fix it.

All you have to do is set the auto close timer and thenwait for the alarm clock to go off.

In most cases it is enough to establish the routine and you can proceed with the configuration. Some owners also had to disable and re-enable this feature to avoid minor bugs.

Just be patient with the device and experiment with all the settings to find the one that works best for you. I hope it's not too difficult to correct the situation with the auto-lock features.

  1. Problems with accessories

Interference from other wireless devicesand thick walls can cause problems with devices not working.

(Video) Setting Limits on Automatic Gate Opener

So if you run into the same errors, it's a good idea to limit the number of wireless devices near your garage door remote.

6 Common Problems With Ghost Control Gate Openers - DIY Smart Home Hub (5)

It makes no sense to have a bunch of useless wireless devices near the receiver. This will only complicate the situation and you will notice a drop in drive consistency.

So, review the solution accordingly if you are unable to fix the errors.

  1. keyboard problems

It is not uncommon for users to encounter keyboard issues from time to time.

Depending on the condition of your keyboard, there is a possibility that you are dealing with dead batteries in your device. So make sure you check the keyboard battery before relying on a reset operation to fix the device.

If the problem is not resolved after replacing the keyboard batteries,no What you need to do is restart Unitto factory settings.

6 Common Problems With Ghost Control Gate Openers - DIY Smart Home Hub (6)

It fixes all the little keyboard bugs and as long as the control board is working, you don't have to worry about this issue anymore.

  1. transmitter problems

There have also been several reports of poor device performance after owners have used the transmitter.There will be no movement at the gate., and you get no response from the gate.

This Ghost Controls door opener transmitter problem is caused by the wrong position of the drip switch according to experts. Therefore, you must correct the orientation of this switch and try to operate the gate opener again.

  1. wiring conditions

broken cable andCorroded connections are quite common.For users who live in regions with higher humidity.

(Video) What Makes a Good Gate Opener

So, if you also live in similar environmental conditions and the device often does not work properly, then there is a possibility of wiring issues.

The only thing you can do about this problem is to follow the gate opener service requirements.

Ignoring these requirements for too long will create more wiring issues and you can use any cleaner on the market to keep the wiring in perfect condition.

  1. faulty control board

While this issue is not as rare as some of the other options mentioned here, you will encounter some ownerscomplain about this issue on the community forums.

Unfortunately, there's not much you can do about it, and the only solution is to call your dealer to order a replacement unit.

6 Common Problems With Ghost Control Gate Openers - DIY Smart Home Hub (7)

The warranty policy will cover this issue with your gate opener and it is best to get your dealer involved.

So instead of messing with the wires connected to the control board, just ask your dealer to help you with this problem. This will save you a lot of time and effort.


These were some of the most common issues to look out for when purchasing Phantom Controllersgarage door opener.

Fortunately, you can fix most of these issues by following the quick fixes above.

Nonetheless,If you are unlucky enough to discover that the drive is faulty, the only remedy is to get a replacement.. You cannot expect consistent performance from a failed drive, and getting a new one is the only logical step.

(Video) Automatic Gate Opener Not Working

The advantage of this is that thethe warranty must cover all damage, and you can show proof of purchase to get a new device. Once the warranty claim is verified, you should receive your new device within two to three business days.

Be sure to contact your dealer for details on the complaints procedure. There is no point in waiting alone and the customer support team will guide you better.So be sure to consult these experts.


1. DIY Cheap Remote Gate Access Control and GSM Intercom System
(Jack of All Master of None)
2. Diagnosing Gate Malfunction in the Closed Position
3. How To: Troubleshooting Exit Wands
4. ✅Top 10 Best Automatic Gate Openers in 2022 Reviews
(The10 Bestones)
5. Testing Battery Voltage for Driveway Gate Openers
6. How To Program Your Garage Door Opener On Your BMW
Top Articles
Latest Posts
Article information

Author: Dong Thiel

Last Updated: 05/14/2023

Views: 6079

Rating: 4.9 / 5 (79 voted)

Reviews: 86% of readers found this page helpful

Author information

Name: Dong Thiel

Birthday: 2001-07-14

Address: 2865 Kasha Unions, West Corrinne, AK 05708-1071

Phone: +3512198379449

Job: Design Planner

Hobby: Graffiti, Foreign language learning, Gambling, Metalworking, Rowing, Sculling, Sewing

Introduction: My name is Dong Thiel, I am a brainy, happy, tasty, lively, splendid, talented, cooperative person who loves writing and wants to share my knowledge and understanding with you.